What should I check before an RC plane's maiden flight?
Check the balance point (CG), that every control surface moves the right way and by the right amount, the failsafe, a range check, a charged battery and a secure prop. Then pick a calm day, plan the takeoff and the first circuit, and climb to a safe height before trimming. Rehearse the whole sequence in a simulator so the field part is routine.
Fly Before is the RC flight simulator for Mac that runs real ArduPilot in one click. Plug in your radio and practice every step on your Mac before you go to the field. See what Fly Before does
A maiden flight is short and busy. Most maiden crashes we read about in builder groups trace back to something that could have been caught on the bench: a tail-heavy plane, a reversed aileron, a weak launch. A printed checklist and a rehearsal take the guesswork out. Adapt the list to your plane and your manual; the designer's numbers always win over generic advice.
On the bench, the day before
| Check | How | Why |
|---|---|---|
| CG | Balance on your fingertips or a balancer at the manual's CG mark, with the flight battery installed | Tail-heavy planes are often uncontrollable; slightly nose-heavy is safer for a first flight |
| Control directions | Stand behind the plane. Right stick: right aileron up. Pull: elevator up. Right rudder: rudder right | A reversed surface is a guaranteed crash |
| Control throws | Measure at the widest point against the manual; set low rates for the maiden | Too much throw makes a new plane twitchy |
| Linkages and hinges | Wiggle every surface and horn; check clevises are closed | Flutter and loose linkages fail in the air |
| Failsafe | Set it in the receiver or flight controller; test with the prop off | You need to know what happens when the link drops |
| Power system | Measure current at full throttle with a watt meter | Estimates are estimates; an overloaded motor or ESC fails at the worst time |
| Prop | Right direction, balanced, nut tight | A reversed prop gives almost no thrust |
At the field
- Wind: calm, or light and steady straight down the runway. Postpone if it is gusty.
- Range check: use your radio's range-check mode and walk away with a helper moving the surfaces.
- Battery: fully charged flight pack and transmitter.
- Plan: takeoff direction, where you will turn, where you will land, and what you do if the motor stops.
- Helper: for a hand launch, someone who has launched that type before. For a VTOL, a clear area and a plan for the transition.
- Timer: set it short for the first flight. You do not know the real flight time yet.
The flight itself
- Take off or launch into the wind, wings level, firm and positive.
- Climb straight ahead to a safe height before turning. Do not fight trim close to the ground.
- Trim for level flight at a comfortable throttle. Count the clicks so you can transfer them later.
- Check slow flight at height: reduce throttle and see how the plane behaves near the stall.
- Fly a few circuits, then land early with battery to spare.
- After landing, write down trims, flight time, battery used and anything odd.
Rehearse it in the simulator
Fly Before has a First flight with the Explorer lesson that starts with a checklist rehearsal before you fly. If your plane is different, set it up in the Workshop with your motor, prop, battery and CG, and look at the four gauges: power, flight time, slow-flight speed and balance. Then fly the planned sequence a few times, including a motor cut after takeoff (the dead-stick landing lesson) and a lost radio link.
If your plane runs ArduPilot, also rehearse the failsafe and RTL with real ArduPlane code, so you know which way it turns and how high it climbs. See ArduPilot on your Mac.
Simulator numbers, including Fly Before's Workshop, are model output. Measure the CG on the real airframe and the current with a watt meter. A rehearsal makes the sequence familiar; it does not replace the checks.
Printable checklist
- CG at the manual's mark, battery installed
- All control surfaces move the right way (stand behind the plane)
- Throws measured; low rates for the maiden
- Linkages, clevises, hinges and horns secure
- Failsafe set and tested with prop off
- Full-throttle current measured with a watt meter
- Prop direction, balance and nut checked
- Flight battery and transmitter charged
- Range check passed
- Wind calm or steady down the runway
- Takeoff, circuit, landing and dead-stick plan agreed with helper
- Timer set short
- Climb to safe height before trimming
- Note trims, time and battery used after landing
Questions
What is the most common cause of a failed maiden flight?
Builders on forums most often point to a tail-heavy CG, a control surface moving the wrong way, or a weak launch. All three are caught on the ground with a balance check, a control-direction check against the plane, and a planned, firm launch into the wind.
Should I set up a failsafe before the maiden?
Yes. Decide what the plane should do when the radio link is lost, set it in the receiver or flight controller, and test it on the ground by switching the transmitter off with the propeller removed or the plane held securely.
Fly Before: RC Flight Simulator is a native macOS app (Apple Silicon) for flying RC planes and fixed-wing VTOLs that runs real ArduPilot in one click through the free ArduPilot Helper. One-time purchase, not on sale yet.
Sources
- Fly Before user guide: Explorer first-flight lesson with checklist rehearsal, Workshop gauges, failure lessons
- Maiden-crash themes (CG, reversed surfaces, launches) collected from public builder groups and RC forums, summarized in our research notes, November 2026
- Academy of Model Aeronautics, club and safety resources: modelaircraft.org
Changelog
- : First published.